国产SUV精品一区二区62,色一情一伦一区二区三,公好大好硬好深好爽,欧美国产亚洲日韩在线二区

HomeHotlineContact
0position:Home>>News

Analysis of the reasons for the creeping and vibration of the edge milling machine

source:   author: time:2020-08-15 Visits:1884
There are many obvious abnormal phenomena in the milling machine, but in some economic CNC systems, there is no alarm. Even if there is an alarm sometimes, the alarm information shows that it is not the alarm of abnormal phenomenon you see. The creeping and vibration of the milling machine is an obvious example. When the milling machine runs at a low speed, the worktable of the CNC milling machine moves forward in a creeping manner; when the milling machine runs at a high speed, there will be vibration.

Because of the bad lubrication, the friction resistance increases when the milling machine table moves. When the motor is driven, the table does not move forward, which makes the ball screw produce elastic deformation and stores the energy of the motor on the deformation. When the motor continues to drive and the elastic force produced by the stored energy is greater than the static friction force, the milling machine table creeps forward and moves in this way again and again, resulting in crawling phenomenon.

Because the vibration frequency is proportional to the speed of the motor, the first thing to do is to check whether there is a fault in the motor, check the surface condition of the carbon brush and commutator, as well as the mechanical vibration, and check the lubrication of the ball bearing. The whole inspection does not need to be disassembled completely, but can be observed by the inspector. The bearing can listen to the sound with ears To check. If there is no problem, check the tachogenerator. The tachogenerator is usually DC.

A closed loop system may also cause system oscillation due to poor parameter setting. However, the best way to eliminate this oscillation is to reduce its magnification, to adjust RV1 and reverse clock direction in the FANUC system. At this time it can be seen that it will become better immediately. However, because of the relatively small range of RV1 regulating potentiometers, sometimes it can not be adjusted, it can only change the short circuited bar. Cut off the feedback resistance and reduce the magnification of the whole regulator.

More edge milling machines, with pressure beam milling machine, no pressure beam edge milling machine, end face milling machine, end face milling machine, planer. Please pay attention dtchemical.com


All rights reserved:WUXISHI XILI MILLING MACHINE CO.,LTD(dtchemical.com)  Su ICP 15043207-1 Design :25318.cn

午夜视频在线在免费| 精品亚洲成av人在线观看| 日本xxxx色视频在线观看| 丁香美女社区| 欧洲熟妇色xxxx欧美老妇| 狠狠做深爱婷婷久久综合一区| 色www永久免费视频| 2021久久精品国产99国产精品| 成年美女黄网站色大片| 97夜夜澡人人双人人人喊| 粗壮挺进人妻水蜜桃成熟漫画| 少妇被又大又粗又爽毛片| 精品无码一区二区三区爱欲| 97se亚洲综合在线| 欧美综合自拍亚洲综合图片区| 亚洲av不卡一区二区三区| 精品国产一二三产品区别在哪| 人妻色综合网站| 成人网站免费看黄a站视频| 欧美午夜特黄aaaaaa片| 伊人色综合久久天天| 熟妇人妻va精品中文字幕| 亚洲av激情无码专区在线播放| 丰满少妇人妻久久久久久| 国产内射在线激情一区| 国产乱子伦精品视频| 饥渴的熟妇张开腿呻吟视频| 欧美精品videosse精子| 国产小屁孩cao大人| 女局长白白嫩嫩大屁股| 人妻少妇精品视频三区二区一区| 国产97色在线 | 日韩| 欧美金发尤物大战黑人| 综合 欧美 亚洲日本| 国产激情无码一区二区| 大地资源第一在线| 纯爱无遮挡h肉动漫在线播放| 广东少妇大战黑人34厘米视频| 久久久久亚洲av成人人电影| 人禽伦免费交视频播放| 三年片中国在线观看免费大全|